Видео

Hi. I got a 91 Ford f350 7.5 460. Crew cab. What did you have to remove to get the heads off.?

Did you get the full amount of oil in final drive?

Great video I’m ordering my new tracks tomorrow. Really helpful

I have the same problem where is that hole???

Wish they'd make these without so much room. Way to easy to work on

After you safely heat the nut to glowing red with an "induction Heater" you can apply candle wax as a lubricating penetrating oil. The candle wax really traves well by capillary action.

Invest in an "Induction Heater" to more safely heat the stuck fasteners.

Where is the power button

Bahi in 1994 mood all babcat ka chassis name kadr hotha ha pl please bahi in Nathan

Do you hail all the bridges on the same channel?

That outer seal is officially called a "wiper seal" or "dust seal' depending on the manufacturer

Question. F250/F350 (99-04) Front leaf springs are the same? Diesel vs Gasser springs are interchangeable? I know the diesel engine is heavier so those springs would just be more rigid.

Can you do a video on removing the pulley? Please 😮‍💨👊

What is the time it takes to travel from Lockport to brock port on the canal

Hey there! about 9 years ago you had a series for the bob cat, other than the valve adjustment, there were no adjustments that needed to be made for the injectors correct?

I just run across this video I bought one earlier this year and I can't find any one that is selling the housing for the pull start acembly I need the hole acembly if any one can help Im willing to pay for one thanks

I’m experiencing the same start up problems where it runs rough (I was thinking a bad plug), smokes and sputters but in 10 - 30 seconds runs fine. Lately it’s been doing the same every few minutes for about 10 seconds, then returning to normal. At 3:50 on the video you speak about disassembling the electric choke and adding a capful of oil in an access hole and working the assembly to get rid of the “crunchiness” - my question is the location of the access hole - is it on top of the black cap or do you have to disassemble the electric choke to find the hole.

Best video on YT for brake job on an F-350. Thank you…

Great video ....as usual! Where we live and cruise, we don't have locks to go through...just the Atlantic and the Gulf of St. Lawrence. I know there's a charge to use the locks in Ontario, is there a charge to use those locks your using and if so, is it a seasonal pass or a single use fee and of course, how much? Keep the videos coming and have a GREAT summer!!🍻

In the 50's we had a farm off Allens bridge rd in Eagle Harbor my father was plant manager of friend spray mfg in Gasport

What an awesome way to spend a day with the wind in your hair and dogs beside you. Thanks for the video

My 310 Sundancer is same way doesn't respond right away. I think it has to do with the prop tunnels that these boats have. Great Video, always look forward to your boating videos.

Good video. Noticed on this video your cab mounts need replacing. They are hitting metal on metal

Looked like a great day to travel

this is the only video i can find to help me remove the windows for cleaning

Thank you for your help, I replaced all my rings with no problems at all.

What is the ball and spring I lost mine and need to know what they are to get new ones

I just have to reach over on my boss to change the lever. Same thing to take it off.

what boat you got?

I'll take $5.09. We're paying $5.69 in the Detroit area.

can You please try to find a part number on that roof glass? mine flew off on the highway and i cant find it anywhere to buy

Minimal tools starts off with commercial grade impact l😂

great

Don’t forget to change the hydraulic filter under the cab

You know if you have to switch to centimeters to measure your lash you’re in trouble!

Was that Brian driving by and beeping!?? 😂😂

Perfect instructions!

Type of kit did you order?

Otor was blown.and i have no tools. I dont want to remove the motot i dont have a table.mine is in an rv motorhome.and to put the gaskets.is it better for me to orxer new heads? And water came out through the manifold

Great video

Looks like a cool project. Can't wait to see the end result.

Happy birthday Kim

Sorry for your loss

A little safety tip for you put your tire you took off under the step rail incase something fails and it falls it will act as a jack stand

Where did you get the parts? Or how did you find them?

Where can I find the parts for the pump rebuild? Thanks.

The blue courtesy lights look sweet. That's gonna look good at night.

Man John I wish my impellers were that easy to change.

Just cut my wrap off yesterday.

Sorry to hear about your mom.